Home > Products > Diesel Air Compressors > Mobile 185 CFM Compressor Meet E5 and T4 Exhaust
Self-powered — no mains supply needed on site, just fuel and a level standing area. The Mobile 185 CFM Compressor Meet E5 and T4 Exhaust is built for continuous industrial duty. It runs on a direct-coupled air end with no belts to re-tension, and it is delivered as a complete package — airend, motor, cooler, separator and controller on one base frame — so on-site work is limited to power, piping and a drain.
A single cutaway view of the whole unit: airend, drive motor, separator tank, coolers, filtration and controller mounted on one base frame. Use it to check the space envelope and service access before ordering.
Close-up of this part of the machine.
Close-up of this part of the machine.
Close-up of this part of the machine.
Close-up of this part of the machine.
A single-stage oil-injected rotary screw airend with asymmetric rotors machined and lapped as a matched pair. Large-diameter rotors run at low speed for a long bearing life and a stable specific power figure.
Close-up of this part of the machine.
Close-up of this part of the machine.
Close-up of this part of the machine.
Close-up of this part of the machine.
Close-up of this part of the machine.
Close-up of this part of the machine.
Close-up of this part of the machine.
The full model listing on one panel — power, pressure and capacity for every frame size in the range, so you can pick the frame before going into the detail table.
| Model No. | Free Air Delivery (cfm) | Make | Engine Power | Full Load Speed | Off load Speed | Fuel Tank Capacity | Weight | Outlets | Dimension (mm) | |||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 100 | 116 | 145 | 174 | |||||||||
| psi | psi | psi | psi | hp | rpm | rpm | L | kg | L | W | H | |
| WGD185 | 185 | 150 | XICHAI | 50 | 2650 | 1450 | 80 | 900 | 2×3/4" | 3050 | 1650 | 1500 |
| WGD185 SKID | 185 | 150 | XICHAI | 50 | 2650 | 1450 | 80 | 825 | 2×3/4" | 2010 | 1240 | 1100 |
Rock drilling, blasting and bench work with no mains power.
Breaking, compaction and pipeline pressure testing.
Pipe testing, cleaning and repair crews.
Spraying, breaking and general site air.
Field service and remote wellsite work.
Any location where a generator would be a separate cost.
Standby air for rescue and recovery work.
Towable units for rental companies.
Dust suppression, cleaning and conveying air.
Every unit ships with an 18-month warranty on the air end and 12 months on the rest of the machine, counted from commissioning or 24 months from shipment, whichever comes first.
Each machine is run on the test bench and the delivered flow, working pressure, current draw and noise level are recorded against the datasheet before it is crated.
Installation drawings, piping diagrams and a commissioning checklist are supplied with the machine, with remote engineering support during start-up.
Airends, motors, controllers, filters, separators and cooler assemblies are held in our own warehouse, so service parts are not tied to a production run.
No. The unit is driven by its own diesel engine, so it only needs fuel and a level standing area. That is the reason these machines are used on road, quarry and pipeline work.
The fuel tank capacity and the engine load determine the running time; both are in the specification table. For long shifts we recommend the skid or portable variant with the larger tank.
The portable variant comes on a towable chassis. Check the local road regulations for the towing speed and the brake requirements before moving it between sites.
Optional engine pre-heat and a larger battery are available for cold-start conditions — tell us the lowest expected ambient temperature when you order.
Tell us your requirements and our sales team will reply within 24 hours.
