Three-in-one design: screw compressor, air receiver and refrigerated dryer on one base. The 2.2-5.5kW Tank Mounted Air Compressor is built for continuous industrial duty. It runs on a direct-coupled air end with no belts to re-tension, and it is delivered as a complete package — airend, motor, cooler, separator and controller on one base frame — so on-site work is limited to power, piping and a drain.
A single cutaway view of the whole unit: airend, drive motor, separator tank, coolers, filtration and controller mounted on one base frame. Use it to check the space envelope and service access before ordering.
A single-stage oil-injected rotary screw airend with asymmetric rotors machined and lapped as a matched pair. Large-diameter rotors run at low speed for a long bearing life and a stable specific power figure.
Vector inverter that trims motor speed to match actual air demand instead of loading and unloading at a fixed speed. Highest saving on installations that sit part-loaded most of the day.
Pressure vessel that buffers the demand peaks so the compressor is not cycling on every short burst of air use.
The machine as shipped: canopy, control panel, service doors and mounting feet.
The machine as shipped: canopy, control panel, service doors and mounting feet.
Close-up of this part of the machine.
| Model | Working pressure | Capacity FAD | Motor Power | Tank Capacity | Noise Level | Oulet | Weight | Dimension (mm) | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| bar | psi | cfm | m3/min | hp | kw | L | Db | Diameter | Kg | L | W | H | |
| WZS2.2 | 8 | 116 | 11 | 0.32 | 3 | 2.2 | 110 | 54+/-3 | G1/2 | 180 | 1090 | 450 | 1110 |
| 10 | 145 | 9.5 | 0.28 | ||||||||||
| WZS3.0 | 8 | 116 | 16 | 0.44 | 4 | 3 | 110 | 55+/-3 | G1/2 | 190 | 1090 | 450 | 1110 |
| 10 | 145 | 14 | 0.39 | ||||||||||
| WZS4.0 | 8 | 116 | 20 | 0.58 | 5.5 | 4 | 110 | 57+/-3 | G1/2 | 200 | 1090 | 450 | 1110 |
| 10 | 145 | 18 | 0.52 | ||||||||||
| WZS5.5 | 8 | 116 | 27 | 0.76 | 7.5 | 5.5 | 110 | 59+/-3 | G1/2 | 215 | 1090 | 450 | 1110 |
| 10 | 145 | 24 | 0.68 | ||||||||||
Spraying, tyre inflation and air tools on one compact unit.
PCB cleaning and SMT line air supply.
Clean, dry air at the machine.
Packaging and process air with the dryer in line.
Small, quiet, dry air supply.
General plant air in a small footprint.
One unit covering the whole shop floor.
Every unit ships with an 18-month warranty on the air end and 12 months on the rest of the machine, counted from commissioning or 24 months from shipment, whichever comes first.
Each machine is run on the test bench and the delivered flow, working pressure, current draw and noise level are recorded against the datasheet before it is crated.
Installation drawings, piping diagrams and a commissioning checklist are supplied with the machine, with remote engineering support during start-up.
Airends, motors, controllers, filters, separators and cooler assemblies are held in our own warehouse, so service parts are not tied to a production run.
The compressor, the air receiver and (on this model) the refrigerated dryer are built onto one base, so the whole air station arrives as a single unit and only needs power and a drain.
Usually not. The on-board tank buffers the normal demand peaks. A separate receiver only helps where you have a very large intermittent demand.
It is designed for indoor installation on a level floor with enough clearance at the service doors. Do not install it in a room without ventilation — the heat has to go somewhere.
This model includes the refrigerated dryer. If your process is not sensitive to moisture you can order the compressor and tank without it.
Tell us your requirements and our sales team will reply within 24 hours.
